Local contractor in 32068

Upon inspection, we found that the power supply at the meter main was compromised due to a missing leg from the incoming feed. To resolve this, we adjusted the wiring for the lights, ensuring they operated effectively on the remaining operational power and successfully restored functionality to the affected areas.

An inoperable living room outlet was flagged during inspection. Upon investigation, we found that a switch near the kitchen controlled this outlet, restoring its functionality. Additionally, we addressed the front entryway light, which was not operational due to its dusk to dawn feature, preventing it from turning on during daylight hours.

Outdated bathroom vanity lights needed to be upgraded for a more modern look. We expertly removed the existing fixtures and installed the customer-supplied LED vanity lights, enhancing both the functionality and aesthetic appeal of the bathroom environment.

The existing three-conductor SE feeder was found to be non-compliant as it should not be buried. We removed the old feeder and installed a PVC conduit from the trailer pole to the panel. A new 2-2-2-4 USE-2 wire was laid to meet NEC Code standards, and appropriate ground bars were added to properly separate grounds and neutrals in the panel.

Intermittent functionality of the EV charger signaled an issue, leading us to inspect the panel. Upon examination, we found that both the EV and air handler breakers had failed, necessitating their removal. We replaced them with new breakers and discovered loose connections on the air handler, which likely contributed to the failure. Using a thermal camera, we checked for any hot spots to ensure safety.

Power flickering and tripping breakers indicated a potential issue, which we quickly addressed. Upon inspection, we found a loose neutral connection within the panel. We secured the connection and added a jumper to ensure both sides of the neutral bus were properly tied together, restoring stable power to the circuits.

The issue involved a breaker consistently tripping whenever the front porch switch was activated. After investigating the panel, we discovered that the existing breaker was malfunctioning. We proceeded to remove the faulty breaker and installed a new one, restoring functionality to the porch switch.

After receiving a call about sparking from the electrical panel and loss of power in half the home, we arrived to find that the B phase had failed due to a lightning strike. We removed the damaged 200 amp panel and installed a new one, complete with new feeder breakers and a whole home surge protector to prevent future incidents.

To enhance safety and functionality, we installed a back-to-back receptacle on the front porch, incorporating a GFCI outlet and a bell box with an in-use cover. After completion, we verified that the voltage levels were accurate and the system operated correctly, ensuring everything was up to code and ready for use.

To enhance airflow in the bedroom, we installed a fan rated box at the center of the room. We ran 14/3 Romex wiring from the switch to the fan box and wired a switched receptacle to keep it constantly hot, allowing for convenient fan control. The setup ensures optimal functionality and comfort.

After a lightning strike led to a total of 14 inoperative bulbs, we promptly arrived to address the issue. We successfully repaired all faulty lights, ensuring the home was fully illuminated once again. Additionally, we left extra replacement bulbs with the tenant for future use.

Several breakers had tripped, causing electrical disruptions. We reset the breakers and confirmed proper voltage and operation throughout the system. Upon inspection, we identified a loose connection on the air handler breaker that led to overheating. We resolved the issue and informed property management that a replacement may be necessary, although it was functioning correctly at the time.

Responded to a loss of power in the garage and diagnosed an issue with the neutral connection affecting the circuit. Accessed the electrical panel and corrected loose and improperly terminated neutral connections, including service conductors that were not properly secured from the original installation. After making necessary corrections and tightening all connections, restored power and verified proper voltage and operation.

The outdated landscape lighting around the backyard pool deck was in desperate need of an upgrade. We swiftly removed the old fixtures and installed the customer-supplied lights, enhancing the overall ambiance. Additionally, we replaced the front yard lighting, upgraded a coach light at the back of the house, and revamped the foyer with a SwitchX dimmer and track strip lighting. The dining room chandelier switch was also replaced, ensuring proper voltage and operation were verified upon completion.

To enhance the functionality of the new sitting room addition, we installed a dedicated circuit from the electrical panel directly to the new space. This included the installation of a dual function breaker in the panel, as well as six new outlets for added convenience. We also connected a switch and the customer-supplied light fixture to complete the setup.

Troubleshot a loss of power affecting the living room and master bedroom after the customer reported a burning odor. Located a failed receptacle with a loose neutral connection caused by a back-stabbed termination. Removed the damaged receptacle and installed a new tamper-resistant receptacle using secure terminal connections. Restored power and verified proper voltage and operation upon completion.

To provide reliable power for the outdoor water softener, we connected it to the garage's electrical system. We installed a GFCI-protected quad outlet in the garage, ensuring safe outdoor use. Additionally, we mounted an outdoor-rated bell box with an in-use cover for added protection and convenience.

To ensure reliable power for a refrigerator in the garage, we installed a new dedicated 20-amp circuit and receptacle directly beneath the electrical panel. After the installation was complete, we verified that the voltage was correct and the system operated efficiently, providing peace of mind for the customer.

Installed a new 30-amp dedicated circuit for the pool heater in the customer-selected location. Installed the required GFCI breaker, ran new wiring from the electrical panel to the equipment location, and completed the final connection with flexible conduit. Verified proper voltage and operation upon completion.

To ensure the refrigerator operates efficiently, a dedicated 20 amp circuit was installed below the electrical panel. This installation provides a reliable power source, preventing overloads and ensuring optimal performance for the appliance. We meticulously connected the circuit to meet all safety standards, offering peace of mind for the homeowner.

To ensure reliable functionality for the outdoor water softener, we connected it to the garage power supply and installed a GFCI-protected quad outlet. Additionally, we mounted an outdoor-rated bell box with an in-use cover, ensuring safe and convenient access for outdoor electrical needs.

Responded to loss of power affecting portions of the home. Identified a failed two-pole breaker that had been improperly used for two separate single-pole circuits. Removed and replaced with two correctly sized single-pole breakers. Restored power and verified proper voltage and operation upon completion.

The loss of power in the bedroom indicated an electrical issue that needed urgent attention. Upon investigation, we discovered that the septic pump was improperly tied into the bedroom circuit, causing a fault. We removed the damaged wire and informed the customer that a new feed line would be necessary to properly power the septic pump.

An outdoor receptacle circuit was non-functional due to loose wiring and a damaged weatherproof cover. We successfully repaired it by securely reconnecting the wiring at the GFCI receptacle and replacing the cover. After ensuring all connections were tight, we confirmed proper voltage and functionality of the circuit.

Replaced the existing 200-amp Challenger electrical panel with a new GE panel, including all new circuit breakers and a whole-home surge protector, to meet insurance requirements and improve electrical safety. Installed new smoke detectors throughout the home as required by local code.

Responded to an emergency service call after the customer reported a burning smell coming from the electrical panel. Diagnosed a loose connection on the breaker supplying the A/C heat circuit, which caused the breaker to overheat and become damaged. Replaced the failed 50-amp breaker, secured all connections, and verified proper voltage and operation upon completion.

Responded to an emergency service call for a lighting issue. Diagnosed a failed switch caused by a burned contact from a loose connection. Reconnected the wiring to an unused contact, secured all terminations, and restored proper operation.

Repaired an outdoor GFCI circuit by reconnecting and securing loose wiring, replacing the missing weatherproof cover hardware, and restoring power to the downstream circuit. Verified proper operation upon completion.

Replaced the existing 200-amp Federal Pacific electrical panel with a new 200-amp ABB panel, including new circuit breakers and a whole-home surge protector. Installed smoke detectors as required by local code.

Installed a new dedicated circuit from the electrical panel for an EV charger. Installed a weather-resistant receptacle and customer-supplied charger at the front of the home, along with a 50-amp GFCI breaker to meet current code requirements. Verified proper voltage and operation upon completion.